Our Top 50 Picks: What To Look For At The World Of Concrete 2009
December 2008As the new year rolls around, we at Modern Contractor Solutions are gearing up for the World of Concrete in Las Vegas, Nevada, February 2–6, 2009. Held at the Las Vegas Convention Center, the World of Concrete is the only annual international event dedicated to the commercial concrete and masonry construction industries, with 1,700-plus leading industry suppliers in more than 900,000 net square feet of exhibit space. The show always features innovative products, technologies, tools, and equipment, and this year expectations are high for a riveting experience. Attending contractors will find educational opportunities, tools, and equipment that can be used to take their businesses to the next level of success.
Indoor and outdoor exhibits will feature demonstrations, ideas, and more than 150 seminars packed with powerful strategies and the knowledge contractors need. Please see the World of Concrete floor plan below to map out your experience.
We would love for you to come by Booth #S20914 and visit with us at the show—our goal is to learn more about our readers and introduce contractors to our magazine, which is full of information designed to help you improve and grow your business with the latest jobsite and management techniques, software and technology, safety practices, and more. In the meantime, check out our Top 50 Picks on the next few pages. These exhibits promise to deliver, and we can’t wait to see them—and you—at the show.
TYMCO Engineering Dustless Sweeper
Tymco Engineering has designed a dustless sweeper for even the most severe cleaning jobs. The Tymco DST-6 not only removes dirt, dust, and debris from the sweeping surface, but it also cleans the exhausted air to 99.999 percent of 0.5 micron size particles. Tymco’s patented filtration system enables the DST-6 to be equally efficient in wet or dry conditions. To learn more, visit Tymco at Booth #N2763.
Max USA Introduces New Rebar Tying Tool
Max USA Corp. announces the availability of its New RB655 Rebar Tying Tool to the U.S. and Canadian markets. This new tool is capable of tying rebar up to #9 x #8 rebar. The tool ties by wrapping 16-gauge TW1525 wire around the tying area, and it cuts and twists in approximately 1 second. For more information, call 800.223.4293 or visit www.maxusacorp.com. Also, be sure to visit Max USA at Booths #N2515 and O30610.
Bobcat Laser Receivers
Bobcat Company, a leader in the compact equipment industry for 50 years, recently introduced new laser receivers for precision grading attachments. Bobcat offers both a laser-guided grader and laser-guided box blade attachment. The new receivers, developed in conjunction with Trimble, are more economical and offer new functionality. Using the new receivers, operators now have access to grade incrementing from inside the cab of certain optioned compact loaders. In addition to the new receivers, Bobcat offers three models of transmitters. For more information, please visit www.bobcat.com or Booth #C5483.
Primaax® EXTM Air Suspension Improves Durability for Vocational Truckers
Hendrickson recently launched the Primaax® EXTM system, an enhanced version of the Primaax heavy-duty, vocational truck air suspension. Refinements in the system include enhanced joint integrity and durability, improved handling, increased air spring capacity, greater disc brake compatibility, and improved resistance to torque rod bushing walk-out. For more information, call 630.910.2800 or visit www.hendrickson-intl.com, or visit Booth #C7584.
Hydro Tek Puts the Cleaning Power of Water in Your Hands
The heavy-duty SC Series skid has been the proven pressure washer choice of construction professionals for more than 20 years. This self-contained, hot water skid is powered by a gas or diesel engine, and is equipped with an onboard 2900w generator to provide supplemental 115v power outlets. For product information, call 800.274.9376, ext. 3, or visit www.hydrotek.us. To learn more, please visit the Hydro Tek Booth #N2201.
VMAC Underhood Air Compressor for Dodge Cummins
The new Vehicle Mounted Air Compressors (VMAC) Underhood Air Compressor system developed for the 6.7L Dodge Cummins Diesel delivers power, payload, and performance. The rotary-screw compressor produces up to 70 cfm and 175 psi of continuous air-on-demand (enough air for a 3/4-inch impact gun to a 90-pound jackhammer), while the lightweight, under-the-hood mounted system saves your service truck valuable payload and deck space. Mounting the air compressor under the hood allows more equipment and personnel to be transported to the jobsite, meaning fewer trips, and reduced fuel and labor costs. For more information, please visit www.vmac.ca or Booth #031016.
Dynapac Concrete Provides Quality Equipment
Dynapac is an international manufacturer of concrete, compaction, paving, and milling equipment. Since the foundation of the company in 1933, Dynapac has focused on performance, service, and reliability in supplying the most competent machinery products for the building and construction industry. Dynapac offers concrete vibrators, vacuum treatment units, ride-on and walk-behind power trowels, grinders and cutters, external vibrators, and WEDA pumps. For more information, please visit Booth #C3932.
Cleform Tool: The Power of Red
The Rock N Roller imprinting system from Cleform Tool will make traditional methods of stamping obsolete. The patented system has the stamping job finished before the pad method has even begun. It also uses half the manpower of traditional methods. There are seven different patterns available in the larger rollers; five are 36 inches wide, and the two texture rollers are 24 inches wide and come with a 9-inch touch-up roller. For more information, please call 800.253.3676 or visit www.cleform.com.
BoMetals Waterstops
BoMetals, Inc., serves the concrete accessory market by manufacturing a wide variety of products used in both commercial and residential construction. These products include a comprehensive offering of PVC, chemical-resistant (TPER), mastic, and hydrophilic waterstops. All BoMetals products are available through a national network of distributors, and the company ships internationally direct from its facility in Carrollton, Georgia. For more information, please call 800.862.4835, visit www.bometals.com, or come by the BoMetals Booth #N3208.
RS Level Markers and Smart Targets
Berntsen International, Inc., has announced the launch of a new line of permanent precision leveling markers and measurement targets. The RS Level Markers and Smart Targets are ideal additions to all surveying and measuring equipment, as they ensure permanent documentation and evidence of all measurement points on the construction site and simplify the tasks of making observations. For more information, please visit Booth #N3012.
Bartell Morrison Power Trowel
The Bartell Morrison Power Trowel is designed, engineered, and built for a competitive edge through greater productivity, durability, and efficiency. New eco-friendly, electric-powered versions are available in two models, the 3-hp B436 and the 2-hp B424. Single-phase versions include 110V and 230V. Models have full Underwriters Laboratories (UL) and Compliance Service of America (CSA) compliance. For more information, visit the Bartell Morrison Booth #O30613.
Budget Supervision in the Palm of Your Hand
ePlanIt recently announced a new Mobile Project Management (MPM) application for iPhone and iTouch devices designed specifically for the construction market. Expanding its suite of construction management tools, this new software simplifies budget management by tracking workers, tasks, units, equipment, and materials in real time. For more information, please call 214.472.3413 or visit the ePlanIt Booth #S21217.
Liebherr To Roll Out the New R924 Compact Swing Excavator
The new R924 Compact Swing excavator is scheduled to make its debut at the 2009 World of Concrete trade show during the Operators’ Precision Challenge. The Compact Swing excavator is a full-size excavator (163 hp) in a compact body; it offers the practicality of a minimal tail-swing excavator while maintaining powerful performance. The Operators’ Precision Challenge will take place at the Gold Lot outside the Las Vegas Convention Center from Tuesday, February 3, to Friday, February 5, 2009. For more information, visit www.likufix-us.com. Also, please visit the Liebherr Booth #N425.
Towmaster Titanium Low-Deck Detachable Gooseneck Trailer
Towmaster’s Titanium low-deck detachable gooseneck trailer with the paver ramp option (not shown) is made for pavers and heavy equipment needing a low load angle. The Titanium features cambered T1 steel flange 20-inch height deck; quick detaching gooseneck; exclusive push-button air pin release; 2-inch white oak deck; and twin inboard hydraulic cylinders. For more information, visit www.towmaster.com or visit the Towmaster Booth #S13621.
A Different Kind of Diamond Grinder From BW Manufacturing, Inc.
The DG-50 Diamond Grinder/Polisher is unlike any other diamond grinder on the market today. What sets this floor grinder apart from all the others is the floating grinding heads and the specially designed shroud that keeps the machine virtually dust free when connected to the SCB-1600, along with removing all material off the floor and reducing cleanup cost. With quadruple, one-piece, 16-inch, rubber-mounted grinding heads (no planetary gears) that are adjusted up and down by air pressure, the grinder offers infinite adjustability. For more information, please visit www.bwmanufacturing.com or stop by Booth #S10843.
Thomas 185 Skid Steer Loader
Thomas Equipment announced its new Thomas 185 Skid Steer Loader is a total upgrade of the famed Thomas 175. The Thomas 185 combines power and rugged dependability with an easy-to-service, no-frills design. The Thomas 185 has a lift height of over 11 feet; 7,200-pound operating weight; 1,850-pound lift capacity; 2-ton-plus breakout force; a 4-cyclinder, 59-hp Tier-3 engine; nearly 8 mph; universal joint; 100-chain-drive; sound kit; lined cab; and self-level control. For more information, visit www.thomas-equipment.com. Also, visit the Thomas Booth #C6689.
Concrete Politics
With the elections finally put to rest, the task of rebuilding our economy and putting Americans back to work begins. Mar-Mac Wire is optimistic that government will now focus on important energy independence opportunities supporting new concrete construction projects to include nuclear plants, windmills, and other “green” technologies. Projects with federal funding typically specify tie wire products that meet Buy American standards, and all Mar-Mac Wire Premium products offer certification to meet this requirement. To learn more, visit the Mar-Mac Wire Booth #N1369.
Ueven Launches New Time and Attendance Technology
After several years of development and testing, Ueven is proud to launch SHARCC® Time & Attendance, which delivers real-time data on employees’ hours, eliminating 50 percent of payroll functions compared to manual time cards. This is accomplished by utilizing biometric technologies, GPS, and wireless internet. For more information, please call 866.503.3836 or visit www.ueven.com, or visit Booth #S20519.
Construction Accessories, Inc., Offers JackJaw® Form Pin Extractor
The JackJaw® form pin extractor, manufactured by Construction Accessories, Inc., makes an easy task of pulling ¾ 3/4- and 7/8-inch-diameter form pins and stakes. The patented jaw and lever mechanism pulls pins straight up out of the ground without bending them, keeping expensive pins straight for hundreds of repeated uses. Pulling straight up is easier, eliminates side loading, and reduces the strain on the operator’s back, and it is safer than striking the pins with a hammer. For more information, visit Booth #N2967.
Maxwell Systems Releases Estimating Concrete Database
Maxwell Systems, Inc., a leading provider of integrated construction business management software solutions, recently released Maxwell Systems™ Estimating Concrete Database. This new product allows concrete and sitework contractors to improve the speed and accuracy of estimating with various user-focused features. The software offers comprehensive updates, fast takeoff, flexibility, quality, and ease of use. For more information, please visit www.maxwellsystems.com or Booth #S20205.
Husqvarna K 3000 Wet: The Solution to Indoor Cutting With Less Noise and Dust
Husqvarna Construction Products recently unveiled a new addition to an already extensive line of power cutters, the K 3000 Wet. This electric power cutter allows the user to cut indoors easily and cost-effectively, without dust. The K 3000 Wet is equipped with a newly developed wet cutting kit that regulates the flow of water and concentrates the spray into a stream and then onto the blade. For more information, please visit Booth #C4849, O30801, O30801a, O30801b, O30801c, and O30801d.
Sonotube Square Concrete Forms Reduce Production Costs
Sonotube square concrete column forms are the newest addition to the Sonotube family of rugged construction forms. From the outside, these forms look like a traditional round form, but inside they contain a square fiberboard insert locked into place with polystyrene. This unique design ensures the finished column is true to form by enabling a square insert to stand strong against the weight and pressure of poured concrete. For more information, please call 888.766.8823, visit www.sonotube.com, or visit Booth #S10639.
On-Board Weighing System for Concrete Mixers
Vulcan On-Board Scales’ weighing system for concrete mixers continually measures your remaining load. Reliable and easy to use, the system operates alone with Vulcan’s time-tested V320 electronics or interfaces with other on-board computer systems. Vulcan offers a seamlessly integrated, custom solution for McNeilus and Oshkosh concrete mixers. Please visit Booth #N2469 at the 2009 World of Concrete to learn more. For more information, call 800.237.0022 or visit www.vulcanscales.com, or visit Booth #N2469.
10C Technologies Offers Revolutionary Battery Chargers
The new charging platform from 10C Technologies uses a patented, low-heat technology to transfer energy faster at safer temperature levels. The technology cuts charging time down to about 15 minutes while extending the life of the batteries. The system actually extends the life of batteries up to two times and revives up to 70 percent of batteries considered ready for recycling. For more information, please visit www.10ctech.com or stop by Booth #S13104.
Building Material Delivery Duo
The MixKing™ and the DumpKing™ from Cart-Away are 10,000-gvw delivery trailers designed to move ready-mix concrete and bulk landscape supplies. At 1.75 yards, the MixKing has over 50 percent greater capacity than the standard Cart-Away concrete mixing trailer. The DumpKing trailer can haul 5 yards of bulk materials and uses electric/hydraulics to tilt and dump. This duo of trailers is part of the self-delivery system that is at the center of the new Cart-Away Supply® rental program. For more information, please visit www.cart-away.com or Booth #N2166.
Fassi Micro Cranes From Fascan International, Inc.
The FASSI Micro Crane Series is perfectly suited for a wide range of applications, including light construction, landscaping, municipal services, agriculture, and more. Affordably priced and packing plenty of power, Fassi Micro Cranes get the job done in a fraction of the time it would take to move equipment and materials manually or with other machinery. Fassi offers 10 models of Micro Cranes, with varying horizontal and vertical reaches. For more information, please visit www.fascan.com or Booth #031869.
Carnie Cap
The Carnie Cap impalement protection system is at the cutting edge in impalement protection. The system utilizes two Carnie Caps to hold an 8-foot span of 2 x 4 lumber suspended above exposed rebar. During an impact, the lumber absorbs the rebar, rather than deflecting it, so there is little chance of impalement. CAL-OSHA approved and National OSHA compliant, the system is inexpensive, easy to use, and stays on, eliminating the need to babysit your rebar caps. Contact 888.743.7725 to get a list of distributors in your area. For more information, please visit Booth #N3040.
New Resource From American Technical Publishers
Concrete Principles features step-by-step placement, consolidation, and finishing procedures for flatwork and structures, as well as formwork and reinforcement requirements. The textbook also addresses applicable Occupational Safety and Health Administration (OSHA) regulations, and American National Standards Institute (ANSI) and American Society for Testing and Materials (ASTM) standards. An overview of concrete composition, analysis and testing, factors affecting concrete quality, basic math fundamentals, and concrete cost estimating complete the textbook. For more information, please visit www.go2atp.com or Booth #S20836.
Using Technology To Make Concrete Easier
One must-see at the 2009 World of Concrete is a 2007 Most Innovative Product, the Lightning Strike roller screed. This screed boasts an impressive level of versatility and features a threaded axle system. A rugged aluminum design allows the screed to be extended and for accessories to be added to quickly customize it to do any kind of flat work, fast. The Lightning Strike is also easy for crews to manage. For more information, please visit www.luraconcretescreed.com or Booths #S13539, #030651, and #SG22618.
Ezebend Rebar Benders and Cutters
There are two available models of rebar benders from EZE Bend: the 1-inch and the 3/4-inch. The rebar bender keeps the operator safe by pulling the rebar against stationary pins, away from the operator. The head can rotate 360 degrees, making it the perfect tool for cast-in-place rebar. There are also two available models for rebar cutters, the 1-inch and the 3/4-inch. The cutter heads feature 360-degree handle rotation, four-sided cutting blocks, hand-operated gauge blocks, shock absorbers, and the lightest weight and smallest size of their classifications. For more information, go to www.ezebend.com or visit booth #N3115.
New Generator From Mi-T-M
Mi-T-M Corporation, which will be at Booth #S14309, has introduced a new addition to its widely popular generator line. The new high-quality diesel generator features a 9.2-hp Yanmar engine with an electric start. The exhaust system features an expansion silencer with cover, and the low-profile, compact design is perfect for the contractor that requires portable equipment. Mi-T-M has built its reputation on innovative engineering design, manufacturing technology, superior quality control, and unmatched customer service. For more information, please call 800.553.9053 or visit www.mitm.com, or visit Booth #S14309.
Advanced Concrete Tools Joins Forces With ENAR Co.
Advanced Concrete Tools, the number one premier screed line, has teamed up with the number one concrete vibrator line in the world, ENAR Co. Be sure to visit World of Concrete 2009 Booth #C4075 to see new designs, products, and ideas only from Advanced Concrete Tools.
New Hot Wire Machine From Demand Products, Inc.
Demand’s new Independent Axis CNC Hot Wire Machine is the latest in an extensive line of foam-cutting equipment for the precast concete industry. Even fluted, tapered columns are no match for this machine. See it demostrated at the WOC Show 2009, Booth #N965. For more information, please visit www.demandfoamcutting.com or call 800.325.7540.
Vertigraph, Inc., Schedules Release of BidScreen XL Version 5
Vertigraph, Inc., a leading supplier of takeoff and estimating software for the construction industry, announces the scheduled release of its enhanced BidScreen XL version 5.0 software on January 1, 2009. BidScreen XL is for estimators and quantity surveyors seeking an easy-to-use, intuitive, on-screen takeoff tool for digital plans that records the quantity takeoff into any Microsoft Excel workbook. BidScreen works with virtually all of the files distributed in the construction industry. More information can be found at www.vertigraph.com, or visit Booth #S21014.
Bostik, Inc., Features Chem-Calk 2020
Chem-Calk 2020 from Bostik, Inc., is a one-component, moisture curable, advanced urethane sealant that offers superior adhesion to vinyl siding, vinyl trim board, and a variety of dissimilar surfaces. It is suitable for most building materials, including stone, masonry, wood, aluminum, and a variety of other metals. Recommended applications include vinyl siding, vinyl trim board and other engineered woods, as well as other perimeter sealing applications, such as windows and doors. Chem-Calk 2020 has a non-sag consistency suitable for most vertical applications. Its physical properties remained relatively unchanged throughout a wide temperature range (-40°F to 180°F). For more information, please visit www.bostik-us.com or come by Booths #S22305 and #SG22621.
InSite Software, Inc., Offers Comprehensive Estimating Software
InSite SiteWork™ Earthwork & Utility Estimating Software calculates cuts and fills, stripping, strata quantities, subgrade materials, topsoil respread, areas, lengths, trench excavation and backfill from CAD, paper and image (PDF, TIF, DWF, etc.). View and print 3-D, X-sections, and scaled plans. Create global positioning system (GPS) machine control models and construction layout data with Field General Construction Layout Software. For more information, please call 877.746.7483 or visit www.insitesoftware.com, or visit Booth #S20911.
RAM Laptop Mounting Systems
RAM Vehicle Mounts are designed for the most popular cars, trucks, and fleet vehicles on the road. These heavy-duty steel laptop bases are custom formed to fit specific vehicle models. Using the front bench or passenger-side seat rail bolts as attachment points, existing hardware in the vehicle is all that is required to secure these bases. If needed, additional hardware is supplied. Because of their unique ability to absorb damaging shock and vibration, RAM Mounting desks are the perfect choice for securing computers and electronics of any type. RAM Mounts are manufactured in the United States and come with a lifetime warranty. For more information, visit www.ram-mount.com.
Panther® Series SRLs: Substantially Built With Safety in Mind
Elk River, Inc., introduces the Panther® Series SRLs, specifically built with the highly trained worker in mind. Fall Arrest is serious business, and the new Panther Self-Retracting Lifeline is a serious solution to this demanding application. Designed with an integral spring-locking mechanism to pay out and retract the 3/16-inch galvanized steel cable lifeline, the Panther secures the worker where a dangerous fall could occur. These SRLs are lightweight yet strong, compact, and are available in lengths of 15, 20, 30, 50, and 65 feet for the user. For more information, please visit www.elkriver.com or Booth #S11051.
Zimmerman Industries Mobile Concrete Mixers
Zimmerman Industries is a manufacturer of mobile and stationary concrete mixing plants. Zimmerman Mobile mixed concrete is a technique of mixing concrete where the ingredients are proportioned “volumetrically” on the truck by a patented chain feed system and adjustable gate. The Zimmerman 400-N is available in models with a 4- to 11-yard capacity and comes with a hydraulic lift and a power swing standard, plus many additional options that are designed to meet your specific needs. For more information, please call 717.733.6166, visit www.zimmermanindustries.com, or visit Booths #N1429 and #031835.
The B-16 and B-21 From Miller Spreader
Since their introduction over 15 years ago, the 16-cubic-foot B-16 and the 21-cubic-foot B-21 have earned their rank as the standard by which all power buggies are judged. Backed by Miller’s 6-year limited warranty, the B-16’s and B-21’s massive 2-inch-thick, solid steel frame is tank-tough and provides unparalleled strength and durability. Their low center of gravity and ideal weight distribution mean excellent traction in real-world jobsite conditions. These products are made in the USA. For more information, please visit www.millerspreader.com or Booth #N2015.
Cyclone Drop Hammer
When it comes to concrete flatwork demolition, the Stanley Cyclone Drop Hammer is second to none. Designed specifically for hammering flat concrete into small, manageable pieces, the Drop Hammer will not only make your job easier, but it will save you time and money as well. The Drop Hammer is available exclusively from Stanley Hydraulic Tools. For more information, please call 800.972.2647 or visit www.stanleyhydraulic.com, or visit Booth #C4129.
Foundation Software Offers New Module
Foundation Software, developer of FOUNDATION® for Windows® construction accounting software, recently added a new module to further enhance its system’s powerful job cost reporting capabilities. The Executive Dashboard allows users to easily view and analyze key job cost and financial data at a glance, and then drill down into multilayered reports for more detailed information. Colorful bar graphs and pie charts help contractors visualize progress and performance, and a scrolling ticker contains real-time aggregate data for an instant financial update. Stop by Foundation Software’s Booth #S20811 for a live demonstration, visit www.foundationsoft.com, or call 800.246.0800 for more details.
Professional Concrete Sealer and Form Oil Sprayer: One Sprayer Applies Both
Why have two sprayers when you can use one for both form oil and sealer? B&G Equipment’s sprayer features a heavy density polyethylene tank; a heavy-duty, 18-inch brass extension; professional brass shut-off; a wide funnel top for ease of filling and pouring; and a heavy-duty, cast-iron, comfort grip handle. Other features include a 4-foot, professional-grade hose; Viton® equipped; a form oil tip to dispense 35-percent solids and a fan spray tip; a repairable pump assembly; a 5-year tank warranty; and an available parts program. For more information, please call 800.544.8811 or visit www.bgequip.com or Booth #S12320.
Carlson Grade Supervisor v1.0
This new software from Carlson is designed specifically for site supervisors, inspectors, and grade checkers, providing a powerful, yet easy to learn and use 3-D site management system. Productivity will increase, accuracy will improve, and all bid specs will tighten with the help of Carlson Grade Supervisor, which provides direct import of DWG files, DXF files, and machine control files, including tn3, gc3, and ln3. Supervisors can get daily, weekly, or anytime volumes, track real-time cut and fill, plus collect and stake points. The software, which works either on a pole or in a truck, supports most all GPS/GNSS receivers and is Windows XP/Vista compatible. For more information, please visit www.carlsonsw.com or Booth #S20211.
Ditch Witch® Zahn® R300
The Ditch Witch organization, the industry leader in the design and manufacture of underground construction equipment, is exhibiting at Booth #C7568 at World of Concrete. Stop by to see the Zahn® R300, designed to be more powerful, more productive, and faster than any trencher in the 30-hp class. The Zahn R300 includes a Kohler® gas engine, operator’s console, and articulation joint that enables the front end to perform like a dedicated unit. The four-wheel-drive R300 accepts up to seven types of front ends: trencher, plow, dumper, tiller, backhoe, stump grinder, and a tool carrier that can drive more than 40 quick-change attachments. For more information about the Zahn R300, please call 800.654.6481 or visit www.ditchwitch.com.
Baldwin Filters’ PureForce Line
PureForce hydraulic filters with the L-Lock™ hem are available in 4- and 5-inch diameters and are rated with 500- and 350-psi working pressures, respectively. This pressure capability makes these filters suitable for use in hydrostatic charge pump circuits or in other medium-pressure systems that would otherwise require more expensive, canister-style filters. Results show that the Baldwin PureForce hydraulic filters rate higher in burst and impulse tests than competitive filters in the same class. These filters are designed to be used with the PureForce die-cast aluminum bases, which incorporate steel studs that provide additional strength and flow properties. Rounding out the PureForce offering are four new indicators, including visual and electrical styles. For more information, please visit www.baldwinfilter.com or Booth #C7594.
Powers Fasteners Introduces The Snake™+ Self-Tapping Anchor
The Snake™+ is an all-steel, self-tapping anchor. Designed for use in concrete and suited for overhead applications, it combines holding strength with the aesthetic advantages of a flush ceiling mount. The Snake+ sets into a drilled hole with an impact wrench and requires no hammering. It is ICC-ES Approved ESR-2272. For more information on The Snake+, go to www.powers.com or visit Booth #N1624.
Amvic Releases a NEW Tblock Insulated Concrete Form (ICF)
Amvic Building System recently released a new T‐block insulated concrete form (ICF) for the company’s current 6- and 8-inch ICF lines for field testing. It will be available in two configurations. The T‐block will feature the patented 1-inch-deep FormLock™ reversible interlock, which connects the forms tightly together without the need for gluing or taping. They will also contain 100-percent recycled polypropylene webs, which will hold the three panels of expanded polystyrene (EPS) together, hold reinforcing steel, and act as furring strips for interior and exterior finishings. For more information, please visit www.amvicsystem.com or Booth #N459.
World Introduction of the Brokk 400
With a weight of 10,583 pounds and equipped with a 1,400-foot-pound hammer, the Brokk 400 is by far the largest and most powerful demolition machine in the Brokk family. Like its smaller family members the Brokk 50, 90, 180, and 330, the 400 has all unique Brokk features, such as electric power, remote-controlled operation, compact size, and low weight. Equipped with one of many high-powered tools, typical applications for the Brokk 400 would be heavy industrial work, infrastructure work, and heavy construction demolition. For more information, please visit www.brokk.com or Booths #C7382 and #030626.
Wacker Neuson Introduces New Generation of Compact Light Towers
Wacker Neuson is launching a new series of light towers that incorporates a sleek, durable design, quieter operation, and excellent lighting features. The new LTN 6 (Light Tower Narrow body, 6 kW generator), with its compact design, takes up less room on the jobsite, plus reduces freight costs by allowing more units to be transported on a truckload. The housing has been changed to a unique streamlined, curved design made from a high-impact plastic, which extends the life of the unit, especially in the harsh elements. For more information, please visit www.wackerneuson.com or Booths #C4215 and #030346.
Download a pdf version of this article. | Adobe Reader is required.